What Is a Flitch Beam? Flitch Plates Explained
A flitch beam is a steel plate bolted between two timbers. What it is, where it is used, how it compares with a steel beam, and what the engineer specifies.
By J&N Steelcraft UK Ltd · 14 November 2026
A flitch beam is a steel plate sandwiched between two timber joists and bolted through, so the steel and timber act together as one beam. The steel adds strength and stiffness, and the timber on each side gives you something to nail and screw into. Flitch beams turn up most often in loft conversions and in houses where a beam has to sit within the depth of a timber floor.
How a flitch beam works
The timbers on each side are called the flitches, and the steel in the middle is the flitch plate. Bolts pass through all three at regular centres, with large washers on the timber faces, and clamp them together.
Under load, the steel plate carries most of the bending, because steel is far stiffer than timber. The timbers keep the thin plate from buckling sideways and spread the load into the bolts. The result is a beam that's much stronger than the timbers alone, and still made mostly of timber on the outside.
Where flitch beams are used
- Loft conversions. The new floor often needs a beam to support joists or to trim around the new staircase opening. A flitch beam can be the same depth as the new joists, so the floor stays flat and the joists hang off it with ordinary timber hangers.
- Strengthening an existing timber beam. A steel plate can be bolted alongside a beam that's already in place, which avoids taking it out.
- Openings in timber floors. Where a stairwell, chimney breast or new opening interrupts the joists, the trimmer beams around it often need to be stronger than timber alone.
- Timber-framed houses and extensions. In a timber structure, a beam that the rest of the frame can be fixed to directly is simpler to build around than a bare steel section.
Flitch beam or steel beam?
A rolled steel beam, such as a universal beam or an RSJ, and a flitch beam can often do the same job. The choice usually comes down to the building:
| Flitch beam | Steel beam (UB or RSJ) | |
|---|---|---|
| Strength for its depth | Lower, so it may need to be wider or deeper | Higher, so it can be shallower |
| Getting it into the house | Lighter pieces, assembled in place | One heavier section, or bolted lengths |
| Fixing timber to it | Nail or screw straight into the timber | Needs timber packers bolted into the web |
| Matching a timber floor | Same depth as the joists | Often packed out to suit the joists |
In a loft, the deciding factor is often access. The steel plate and the timbers can be carried up separately and bolted together where they're needed, whereas a long steel beam may have to come in through a window or the roof. See what is an RSJ? for how rolled beams compare.
What the engineer specifies
A flitch beam is a structural element, so it's designed by a structural engineer like any other beam. Their calculations set:
- The plate. Its thickness, depth and length, and the steel grade.
- The timbers. Their size and strength grade, usually matched to the joists around them.
- The bolts. Their size, the spacing along the beam, and whether the holes are staggered top and bottom.
- The washers. Large washers spread the bolt load into the timber so it doesn't crush.
- The bearings. How each end is supported: on a wall, on a padstone, or on a hanger. See what are padstones?
The plate is usually set a little below the top of the timbers, so the floor deck and the ceiling sit on timber and the steel doesn't get in the way of fixings.
Making and fitting a flitch beam
The plate is cut and drilled to the engineer's design before it reaches site. The usual sequence is:
- Fabrication. The plate is cut to length and the bolt holes drilled in the workshop, to the engineer's spacing.
- Marking out. On site, the plate is used as a template to mark and drill the timbers, so the holes line up exactly.
- Assembly. The timbers and plate are bolted together, often in place, and the bolts are tightened.
- Bearing. The ends are set onto their bearings or hangers, as the design shows.
- Retightening. Timber shrinks as it dries, so it's worth checking the bolts again once the building has been heated for a while.
Building regulations
Like any structural beam, a flitch beam needs a structural engineer's calculations and building regulations approval. Building control will want to see the design and inspect the work. In a loft conversion, the beam is also part of the floor that has to meet the fire rules for a new storey, so it's usually protected by the fire-rated ceiling below. See do I need building regs for a steel beam? and steel beam fire protection.
Frequently asked questions
What is a flitch plate? A flitch plate is the steel plate in the middle of a flitch beam. It's bolted between two timbers so the steel and timber work together as one beam.
Why use a flitch beam instead of a steel beam? Mainly for access and fixing. A flitch beam can be carried into a loft in pieces and assembled in place, it can match the depth of the joists, and timber can be fixed straight to it.
Is a flitch beam as strong as a steel beam? It can carry the same load, but it usually needs to be bigger to do it. Your engineer sizes it for the load and span either way.
Do flitch beams need building regulations approval? Yes. A flitch beam is structural, so it needs an engineer's calculations and building control approval, the same as a steel beam.
Can a flitch plate strengthen an existing timber beam? Often, yes. A plate can be bolted to an existing beam in place, if the engineer's checks show that the combined beam and its bearings can take the load.
Can you make flitch plates? If your engineer has designed a flitch beam or a steel beam for your loft or extension, we can fabricate the steel to their drawings. See steel beams for extensions. For more information, contact us.
Need this for a real project?
Tell us what you're planning and our estimating team will advise and quote.
Request a QuoteMore guides
Industrial Walkway Regulations: Width, Guardrails and Flooring
What UK rules apply to industrial steel walkways, gantries and platforms: BS EN ISO 14122, the Work at Height Regulations, width, guardrails, flooring and loads.
GuidesGalvanising vs Powder Coating: Choosing a Finish for Steel
Hot-dip galvanising, powder coating, both together, paint or stainless: how each finish protects steel, where to use it and what to tell your fabricator.
GuidesWhat Is a Stillage? Types, Uses and How to Specify One
What a stillage is, how it differs from a pallet or cage, the common types, and what to decide on load, stacking and finish before you order.